Topics
-
How To: Make a PCI Express Power Connector "As highlighted above, this top section is perfect. Hacking a PSU apart is not the best solution for everyone, but if you are like us you will probably have a dead PSU lying around somewhere. We found the best way to separate the top three pins is to use a hack saw. If you cut from the pin side and angle away from the top three, you have less chance of cutting into the pins you need. A quick clean up with a file or sharp knife will give us an appropriate plug."
-
- 0 replies
- 2.1k views
-
-
Audigy 2 to Audigy 4 softmod "The buzz has actually been around for a while, but I didn't notice it until I saw this thread in our forum. Started by longtime member 5-Clicks, it is titled "Softmod your Audigy/2/Live! into an Audigy 4 Pro!". In it, there is a link to another forum describing how to install Audigy 4 drivers on an Audigy 2 card. Some of the comments in the forums made me curious:"
-
- 0 replies
- 2.1k views
-
-
Titan Amanda TEC (Thermal Electronic Chip) Cooler Review "The Titan Amanda TEC is a tower-design cooler with four heat pipes and two fans for taking air in and exhausting it. The first pair of heat pipes takes heat off the bottom plate of the copper base which is nickel-plated to prevent corrosion (quoting the manufacturer). Next goes a 60W Peltier element that pumps heat up from its bottom to top, above which another nickel-plated copper plate is located. Two more heat pipes take heat away from the top plate. The plates are fastened together with four spring-loaded screws. You can see traces of thermal grease along their edges. Judging by the color and consis…
-
- 3 replies
- 3.2k views
-
-
I'm trying to figure out how to make a plastic case NOT fry my components....I'm not talking about plexi, it's about the same material that a 5-gallon bucket is made out of. Really light, VERY sturdy. I've got the design down, just don't know if I should spray it with metallic paint to make it conductive (which I've seen suggested on other forums) or if there's some way to make it anti-static.... Any suggestions?
-
- 5 replies
- 4.6k views
-
-
Spiderman 3 mod "Pro modders and their creations will draw more traffic for sure, but these mods transition from the realm of "hobbist fun" and its fraternal nature into the serious world of elite precision. I suggest this level only if the intent is brand awareness--like Intel/AMD making a market wide statement about cutting edge segment leading processors in general as opposed to a company like DangerDen wanting to throw a little light on their newest GPU block."
-
- 1 reply
- 4k views
-
-
http://www.media-post.net/coolpcmods.php SUPER BOX was my FAV!
-
- 2 replies
- 3.9k views
-
-
Ultra To Unveil 2000W PSU At CES "If you guys thought a 1000W PSU was impressive, you’ll really want to see the Ultra X3 Modular 2000W that will be unveiled at CES in just a few days."
-
- 3 replies
- 4.5k views
-
-
hello im new to this board this is my case its a Xoxide fireball case with 2 90mm blue led fans and 1 120mm blue fan and also with duel red cathodes i think all around just for case and lights it costs about $65.00 with shipping XD with red cathodes on im usin a AMD Athlon 2400+ (soon to be a 3200+) 1.99 Ghz 2 gigs of ram with a NviDia 6800GT and a 17 inch LCD viewsonic monitor also for gaming i got a Microsoft Forcefeedback Sidewinder joystick a Microsoft Force feedback Steering wheel and a hacked origonal xbox controller (just a wire hack to put a male USB end on the cable)
-
- 1 reply
- 4k views
-
-
http://forums.bit-tech.net/showthread.php?...ge=99&pp=20 http://www.g69t.it/public/Scimitar/G69T_DBSP109.jpg http://www.g69t.it/public/Scimitar/G69T_DBSP121.jpg
-
- 2 replies
- 4k views
-
-
A peek inside Apple's new nano and classic iPods (photos) "The first tear-down photos taken of Apple's new third-generation iPod nano and sixth-generation iPod classic are in, revealing extensive use of adhesive inside the nano and a new support plate behind the classic's noticeably thinner display."
-
- 0 replies
- 3.3k views
-
-
are there any places to get inft to update chips on a videocard, for example its BIOS or support for newer technology like ps 3 just a thought, did some searching way back didnt come up with much but it goes with the idea of just update to newest tech insted of buying a whole new card umm that idea could hit the why they dont do that would befuddle their profits...
-
- 4 replies
- 2.7k views
-
-
Mostly just SATA hard drives are out, but SATA DVD+-RW drives are starting to appear (from Plextor I think).
-
- 7 replies
- 3.2k views
-
-
Measuring the Benefits of AGP: Is PCI-Express Necessary? "During Computex we saw photos of several Intel 925x boards equipped with both PCI Express and AGP slots. Since Intel’s new chipset doesn’t offer simultaneous support for PCI-E and AGP, there was a serious question as to how Gigabyte and ECS (the two manufacturers with boards on display) were accomplishing it." ... ... ... "For the gamer, however, PCI-Express is going to be a non-issue. Given that most games today barely stress the AGP 2x bus, moving to double AGP 8x isn’t going to do anything. It’s the equivalent of widening a highway no one drives on. Had AGP developed in the direction it was intended…
-
- 2 replies
- 2.1k views
-
-
NF7 2.0 & NF7-S 2.0 Although, I'm still using BIOS 18 on my NF7-S and BIOS 17 on my NF7 (havn't re-formatted yet) NF7/NF7-S V2 BIOS 24 * Please use AWDFLASH 8.23D or later to update NF7 series BIOS. With incorrect AWDFLASH version, the GUID will be erased, and leads to IEEE1394 peer to peer function failed. AWDFLASH 8.23K is included in this BIOS package. * Fixed the issue that PS/2 wheel mouse is no response under limited condition: - Use certain PS/2 wheel mouse and certain USB keyboard. - PS/2 wheel mouse works fine but lose response on 1st, 3rd, 5th.... restarting windows. Nevertheless, it works fine on 2nd, 4th.... restarting windows. …
-
will after my falure to find firmware updates for my video card im starting to crack for a video card upgrade. i think CrAzY would be a better term, but ive stalked my prey and think the time is right to strike. they i will be ready for ROME total war!!! hehehehe yes i am cRaZy now where did i put that button here it is anyone know if this would work with a 320 power supply with evething in my sig and 4 extra fans (spairs from past power supplys) for cooling, i know i gots a spair power hook up for it and also a cdrom dive and burrner, i thinking im borderlineing it
-
- 30 replies
- 10.9k views
-
